103 TESTING SLIC3R PROFILE

Slic3r version 9.9. 3mm Orange ABS filament. 230 c. temperature. Slic3r settings are a close approximation to Skeinforge default settings (Durbie Normal) with these changes: Cooling and Retraction values are set at Slic3r default. Infill is changed to Line pattern. Aborted.

Print time: [00:12:00]   Total Service Hours: [70:25:44]

 102 TESTING SLIC3R PROFILE

Changed Slic3r 1.2.9 to older version 9.9. 3mm Orange ABS filament. 230 c. temperature. Slic3r settings are a close approximation to Skeinforge default settings (Durbie Normal) with these changes: Cooling and Retraction values are set at Slic3r default. Infill is changed to Line pattern.

Print time: [00:20:44]   Total Service Hours: [70:13:44]

 101 TESTING SLIC3R PROFILE

Testing organic print at 100mm height. 3mm Orange ABS filament. Sliced with Slic3r  1.2.9 using as close approximation to Skeinforge default settings (Durbie Normal) with these changes: Filament Dimension set to 0.9. Cooling set to Minimum Cooling Speed 2.0 sec. retraction values are set at Slic3r default. Infill is changed to Line pattern. Checked Infill Only Where Needed. Changed support values to: Z distance from 0.2 to 0.3mm. Pattern Spacing from 2.5 to 5.0mm. Interface Pattern Spacing from 0.0 to 3.0 mm. Model has delaminating layers. Odd layer count noticed. Aberration of slicer in general.

Print time: [12:20:41]   Total Service Hours: [69:53:00]

 100 TESTING SLIC3R FLOW PROFILE

Same settings as print [099] printing thing 1019953. 3mm Orange ABS filament. Sliced with Slic3r  1.2.9 using as close approximation to Skeinforge default settings (Durbie Normal) with these changes: Filament Dimension set to 0.9. Cooling set to Minimum Cooling Speed 2.0 sec. retraction values are set at Slic3r default. Infill is changed to Line pattern. Checked Infill Only Where Needed. Aborted.

Print time: [00:20:00]   Total Service Hours: [57:32:19]

 099 TESTING SLIC3R FLOW PROFILE

3mm Orange ABS filament. Sliced with Slic3r  1.2.9 using as close approximation to Skeinforge default settings (Durbie Normal) with these changes: Filament Dimension set to 0.9. Cooling set to Minimum Cooling Speed 2.0 sec. retraction values are set at Slic3r default. Infill is changed to Line pattern. Checked Infill Only Where Needed. Print temperature 215 degrees c.! The intention has been to keep extruder temperature and filament dimension equal with all slicers. This may not be possible.

Print time: [00:21:52]   Total Service Hours: [57:12:19]

 098 TESTING SLIC3R FLOW PROFILE

3mm Orange ABS filament. Sliced with Slic3r  1.2.9 using as close approximation to Skeinforge default settings (Durbie Normal) with these changes: retraction values are set to Retractraction Length: 6.0mm and Speed: 100.0 mm/s. Infill is changed to Line pattern at 15%. Checked Infill Only Where Needed. Changed Cooling Minimum Print Speed to 2 sec. Changed Maximum Print Speed in Autospeed to 32 sec. Changed Extrusion Width to to 75%. Print temperature 230 degrees c.

Print time: [00:24:37]   Total Service Hours: [56:50:27]

 097 TESTING SLIC3R FLOW PROFILE

3mm Orange ABS filament. Sliced with Slic3r  1.2.9 using as close approximation to Skeinforge default settings (Durbie Normal) with these changes: retraction values are set to Retractraction Length: 6.0mm and Speed: 80.0 mm/s. Infill is changed to Line pattern. Checked Infill Only Where Needed. Print temperature 230 degrees c.

Print time: [00:22:04]   Total Service Hours: [56:25:50]